P.T. Bridgeport
Bear; from Pogo, Walt Kelly
Pleased to meet you.
The Network Time Protocol (NTP) is used to synchronize the time of a computer client or server to another server or reference time source, such as a radio or satellite receiver or modem. It provides accuracies typically within a millisecond on LANs and up to a few tens of milliseconds on WANs relative to Coordinated Universal Time (UTC) via a Global Positioning Service (GPS) receiver, for example. Typical NTP configurations utilize multiple redundant servers and diverse network paths in order to achieve high accuracy and reliability. Some configurations include cryptographic authentication to prevent accidental or malicious protocol attacks and some provide automatic server discovery using IP multicast.
Background information on computer network time synchronization can be found on the Executive Summary - Computer Network Time Synchronization page. Discussion on protocol conformance issues and interoperability with previous NTP versions can be found in the Protocol Conformance Statement page. Discussion on how NTP reckons the time can be found in the NTP Timescale and Leap Seconds page. Background information, bibliography and briefing slides suitable for presentations can be found in the Network Time Synchronization Project page. Additional information can be found at the NTP web site www.ntp.org. Please send bug reports to <[email protected]>.
Bringing up a NTP primary server requires a radio or satellite receiver or modem. It is also possible to configure a machine on an isolated network with the local clock driver and have other machines synchronize to it. The distribution includes hardware drivers for the local clock and over three dozen radio clocks and modem services. A list of supported drivers is given in the Reference Clock Drivers page. For most popular workstations marketed by Digital/Compaq, Sun and Hewlett Packard, as well as widely available Unix clones such as FreeBSD and Linux, the automatic build procedures select all drivers that run on the target machine. While this increases the size of the executable binary somewhat, individual drivers can be included or excluded using the configure utility documented in the Configuration Options page.
NTP is by its very nature a complex distributed network application and can be configured and used for a great many widely divergent timekeeping scenarios. The documentation presented on these pages attempts to cover the entire suite of configuration, operation and maintenance facilities which this distribution supports. However, most applications will need only a few of these facilities. If this is the case, the Quick Start page may be useful to get a simple workstation on the air with an existing server.
However, in order to participate in the existing NTP synchronization subnet and obtain accurate, reliable time, it is usually necessary to construct an appropriate configuration file, commonly called ntp.conf, which establishes the servers and/or external receivers or modems to be used by this particular machine. Directions for constructing this file are in the Notes on Configuring NTP and Setting up a NTP Subnet page. However, in many common cases involving simple network topologies and workstations, the configuration data can be specified entirely on the command line for the ntpd - Network Time Protocol (NTP) daemon.
The most important factor in providing accurate, reliable time is the selection of modes and servers to be used in the configuration file. A discussion on the available modes is on the Association Management page. NTP support for one or more computers is normally engineered as part of the existing NTP synchronization subnet. The existing NTP subnet consists of a multiply redundant hierarchy of servers and clients, with each level in the hierarchy identified by stratum number. Primary servers operate at stratum one and provide synchronization to secondary servers operating at stratum two and so on to higher strata. In this hierarchy, clients are simply servers that have no dependents.
The NTP subnet in late 2000 includes over a hundred public primary (stratum 1) servers synchronized directly to UTC by radio, satellite or modem and located in every continent of the globe, including Antarctica. Normally, client workstations and servers with a relatively small number of clients do not synchronize to primary servers. There are over a hundred public secondary (stratum 2) servers synchronized to the primary servers and providing synchronization to a total in excess of 100,000 clients and servers in the Internet. The current lists are maintained in the Information on Time and Frequency Services page, which is updated frequently. There are numerous private primary and secondary servers not normally available to the public as well. You are strongly discouraged from using these servers, since they sometimes hide in little ghettos behind dinky links to the outside world and your traffic can bring up expensive ISDN lines, causing much grief and frustration.
Users are requested to report bugs, offer suggestions and contribute additions to this distribution. The Patching Procedures page suggests procedures which greatly simplify distribution updates, while the Porting Hints page suggest ways to make porting this code to new hardware and operating systems easier. Additional information on reference clock driver construction and debugging can be found in the Reference Clock Drivers page. Further information on NTP in the Internet can be found in the NTP web page.
David L. Mills
<[email protected]>